Yuav Ua Li Cas Txuas Tsis-Xov Galvanized Yeeb Nkab?

Koj puas tawm tsam kom paub yuav ua li cas txuas cov yeeb nkab uas tsis muaj xov galvanized? Txuas cov yeeb nkab uas tsis muaj xov galvanized ua ke siv cov couplings uas tsim cov pob qij txha xauv. Koj yuav tsum paub hom kev sib txuas uas koj tab tom siv rau galvanized tsis-threaded yeeb nkab fittings thiab kuj yog cov txheej txheem kev teeb tsa kom tsis txhob muaj cov yeeb nkab xau. Zoo, Peb yuav tsum mus los ntawm cov txheej txheem los txuas cov yeeb nkab uas tsis muaj xov galvanized!

Cov txheej txheem txuas cov yeeb nkab uas tsis muaj xov galvanized

You have to follow the below-mentioned steps to connect non-threaded Galvanized Pipe:

• Ua ntej no, you have to measure each Pipe’s outer diameter, for this, you have to use a tape measure. Ces, you have to select a standard coupling in the situation if the diameters match correctly. But if the diameters differ, you have to choose a stepped coupling.
• In the next step, you have to analyze the pipe’s galvanized surface to specify that is the coating smooth or rough. Ces, you have to select a coupling manufactured to adjust rough surface pipes, in situation if the galvanized coating seems and senses textured. Li ntawd, yog li, you have to request for a “rough surface” coupling reasons that these have tolerances uneven pipe surfaces’s all types like concrete and cast iron pipes.
• Tam sim no, in this step, align the level of a carpenter against the non-threaded pipe’s end so that the end is fair and square. tom qab ntawd, by using a power saw or hacksaw, you have to cut the end to a court or square each pipe if your sto end is rosypipe ends have been removed with the pipe end’s rough edges with the help of a metal sander.
• The next step is to wipe the pipes using a clean cloth and by using a water-based degreaser. You have to do so to remove dust, av, and stains on the coupling area. You have to put the pipes end together. Ces, you have to center the coupling on the pipe joint, Tom qab ntawd, you have to point out a pencil line on each pipe at coupling’s each end.
• tom qab ntawd, you have to insert the non-threaded galvanized pipe’s one side into the coupling. Tam sim no, you have to align the coupling end with a drawn line on the pipe. Tam sim no, you have to put in the second pipe into the coupling. Ces, you will center the coupling between the two drawn lines.
• In this last step, you have to tighten or pull the fastening bolts until the coupling simply keeps the galvanized pipes in place. You have to use a torque wrench set at the marked torque requirement of coupling to evenly attach the bolts till the time the wrench clicks off.

Huv Galvanized steel yeeb nkab

To clean the galvanized steel pipes, Koj yuav tsum ua raws li cov kauj ruam nram no:

• xub thawj, you have to combine 1-gallon hot water, 1 cup vinegar, Thiab 1/4 cup dishwashing detergent in your bucket.
• tom qab ntawd, you have to dip a soft brush into some soap solution. Thiab tom qab ntawd, you have to scrub the pipe with the help of a small circular swirls.
• Tam sim no, you have to rinse the pipes using some hot water and then dry them.
• Ces, Koj yuav tsum thov cov hlau polish nrog kev pab los ntawm cov khaub hlab tsis muaj lint hauv cov lus tsa suab me me.
• Tam sim no, Koj yuav tsum cia cov hlau tsis muaj xov xov, tom qab ntawd koj so nws kom huv.

FAQs

Xaus

o. s. Hopefully, Koj yuav tau txais ntau cov ntaub ntawv tom qab nyeem tsab xov xwm no!